

What Size AC Do I Need for My Dallas Home?
The right air conditioner is not the biggest one you can buy. It is the one sized to your home's actual cooling load, so it cools evenly and pulls moisture out of the air through a long Dallas summer.
By the HVAC-R Finest team. Updated November 18, 2026.

Tons and BTUs: how AC size is measured
Air conditioners are sized by cooling capacity, not by how big the box is. Capacity is measured in British thermal units, or BTUs, per hour. One ton of cooling equals 12,000 BTU per hour, so a 2-ton system is rated for about 24,000 BTU per hour and a 3-ton system for about 36,000.
Not sure what size you have now? The U.S. Department of Energy suggests checking the model number on the outdoor unit's nameplate. It often contains two digits that show the size: 24 means 2 tons, 36 means 3 tons, 48 means 4 tons and 60 means 5 tons. The old size is not proof of the right size, though.
Why square-foot rules of thumb are only a rough start
You may have heard a quick rule like one ton for every 400 to 500 square feet. The Department of Energy calls this a commonly used estimate, and it also names the problem: the rule ignores local climate and how efficient the house is. In the DOE's own example, one ton can cool 800 to 1,000 square feet of a very efficient house.
So two Dallas homes with the same square footage can need different sizes. An older house with thin attic insulation, single-pane windows and leaky ducts gains heat much faster than a newer, tighter home. The Air Conditioning Contractors of America (ACCA) lists rules like 500 square feet per ton among the reasons systems end up oversized. Treat any square-foot number as a rough starting point only.
What a Manual J load calculation looks at
ACCA Manual J is the nationally recognized standard for figuring out how much heating and cooling a home needs. Instead of guessing from square footage, it adds up where heat actually gets into the house.
Insulation
Insulation in the walls, ceilings and floors, plus the roof color and material over the attic, all change how fast heat moves inside.
Windows and doors
Window area, glass type, coatings and shading from overhangs, screens or trees. Glass is one of the biggest sources of summer heat gain.
Sun exposure
The direction each wall and window faces. West-facing glass takes on strong afternoon sun, so orientation changes the cooling load.
Ductwork
Where the ducts run, how well they are sealed and how well they are insulated. Ducts in a hot attic add to the load.
Ceiling height and air leaks
The home's volume, which depends on ceiling height, and how much outside air leaks in through gaps and cracks.
Occupants and appliances
People and appliances give off heat too. Manual J usually counts occupants as the number of bedrooms plus one.
Problems with an oversized AC
Many people assume a bigger unit cools better. In practice, an oversized system cools the air fast, satisfies the thermostat and shuts off before it has run long enough. This on and off pattern is called short cycling.
Short cycling hurts humidity control. ENERGY STAR explains that an air conditioner has to run long enough for moisture to condense on the indoor coil and drain away. With short runs, less water drains off, and some can evaporate back into the air. The Department of Energy places Texas in its hot-humid region, so this matters here: the house can feel cool but clammy, and damp air can encourage mold and mildew. Our guide to indoor humidity in a Dallas home covers this in more detail.
Frequent starts also add wear. ENERGY STAR notes that oversized units tend to have shorter lives because short cycling puts extra wear on the compressor, and the DOE adds that oversized systems can cost too much and still provide poor comfort.
Problems with an undersized AC
Going too small causes the opposite problem. An undersized system may run for long stretches on the hottest afternoons and still not reach the temperature you set.
Long run times are not always a warning sign, though. A properly sized system is expected to run a lot on very hot days, because Manual J sizes equipment for local outdoor design conditions, not for the hottest day on record. And if your current system cannot keep up, dirty filters, leaky ducts or the wrong refrigerant charge may be to blame, so consider AC repair before you decide to size up.
SEER2 basics: efficiency is separate from size
Size tells you how much cooling a system delivers. SEER2 tells you how efficiently it does it. SEER stands for seasonal energy efficiency ratio: the cooling delivered over a season divided by the electricity used. The higher the number, the less electricity the system needs.
SEER2 is the newer version of the rating, used for federal standards since January 1, 2023. It comes from an updated test meant to better reflect real-world installations, so SEER2 numbers are not directly comparable to older SEER numbers.
Texas is in the DOE's Southeast region. Here, a split-system central air conditioner installed on or after January 1, 2023 must be rated at least 14.3 SEER2 if it is under 45,000 BTU per hour, or 13.8 SEER2 at 45,000 BTU per hour and up. Split-system heat pumps must meet 14.3 SEER2 nationwide.
A higher rating does not make up for the wrong size, although ENERGY STAR notes that variable-speed compressors do a better job of making up for some oversizing.
Questions to ask before you replace your AC
ENERGY STAR advises against assuming your existing system is the right size. Ask these questions first.
- Will the size be based on a load calculation, not just the old unit?
- Have insulation, windows or ducts changed since the old system went in?
- Are the ducts sealed, insulated and sized for the new equipment?
- Which rooms feel hot, stuffy or humid today?
- Does the new system meet the Texas SEER2 minimum?
- Would a two-stage or variable-speed system help with humidity?
How HVAC-R Finest approaches AC sizing
When we plan an AC installation or replacement, we look at the home's size, layout, insulation and existing ductwork. That gives a far clearer picture than square footage alone.
Quotes for AC replacement are free. Request a free quote online, or pre-qualify for financing through OPTIMUS in under 2 minutes with no credit impact. We serve Dallas, DeSoto and nearby cities at (972) 372-4458.
More HVAC Guides
Plain answers to common heating and cooling questions from the HVAC-R Finest team.
Frequently Asked Questions
How many square feet does a 3-ton AC cool?
There is no single answer. The rough rule of one ton per 400 to 500 square feet would put it at about 1,200 to 1,500 square feet, but that rule ignores climate and home efficiency. A load calculation gives the real answer.
How many BTUs is a ton of air conditioning?
One ton of cooling equals 12,000 BTU per hour. A 2.5-ton system is about 30,000 BTU per hour, and a 4-ton system is about 48,000 BTU per hour.
Is a bigger AC better for Texas heat?
Not usually. An oversized unit tends to short cycle, which leaves humidity behind and adds wear on the compressor. The right size is the one that matches your home's calculated cooling load.
What SEER2 rating is required in Dallas?
A new split-system central AC installed in Texas must be at least 14.3 SEER2 below 45,000 BTU per hour and 13.8 SEER2 at 45,000 BTU per hour and above. You can always choose a higher rating.
Get the Right Size AC for Your Home
Request a free AC replacement quote, and we will look at your home's size, layout, insulation and existing ductwork.